8-Inch Encapsulated High-Temp Motor 2791059204

Franklin Electric

8-Inch Encapsulated High-Temp Motor 2791059204

رقم القطعة: franklin-electric-2791059204

لا يعرض أي بائع سعرًا لهذا المنتج بعد.

للطلب والدفع استخدم تطبيق ENG.

الوصف

The 8-inch High-Temp Motor utilizes a distinctive premium encapsulation process and water-soluble coolant to allow dependable, continuous operation in 8" diameter or larger water wells with water temperatures of up to 75 ºC (provided minimum allowable flow rates past the motor are maintained). This submersible motor is powered by design and can handle thrust loads 25% higher than a standard motor without oil. Its superior construction comes with water-lubricated radial and thrust bearings to benefit from a maintenance-free operation. Demanding pumping applications have higher requirements. That’s why Franklin’s Hi-Temp Submersible Motors are engineered and tested to deliver exceptional performance in challenging, high-temperature well applications and/or low-flow conditions. The 8-inch High-Temp Motor utilizes a distinctive premium encapsulation process and water-soluble coolant to allow dependable, continuous operation in 8" diameter or larger water wells with water temperatures of up to 75 ºC (provided minimum allowable flow rates past the motor are maintained). This submersible motor is powered by design and can handle thrust loads 25% higher than a standard motor without oil. Its superior construction comes with water-lubricated radial and thrust bearings to benefit from a maintenance-free operation. Features and benefits: - Up to 167 ºF (75 ºC) ambient temperature - 25% increase in upthrust capability at 30 ºC - 25% increase in downthrust capability at 30 ºC - Wet Well, Reservoir, Low Flow approved in 14” diameter or larger wells with ambient water up to 87 ºF (30 ºC) - High temperature leads - Hermetically sealed stator - Innovative high temperature winding encapsulation system - FE water soluble, high temperature bearing lubrication - Double-flange NEMA mounting for ease of handling and pump mounting - Stainless steel splined shaft for maximum shaft/coupling contact - Full 3525 RPM 60 Hz design point for superior pump performance - SAND FIGHTER Sealing System - Franklin Electric’s exclusive Water-Bloc lead connection - 316 SS, Y-∆ and non-vertical designs available - consult factory

المواصفات

HP 60Hz125 hp
Frequency50Hz/60Hz
PhasesThree-Phase
Amps - Full Load161 A
Amps - Service Factor184 A
Volts380 VAC / 460 VAC
Voltage Tolerance (%)-10.0% / +10.0%
Wire3-Wire
Thrust Bearing Rating10000 lb
Lead Length13 ft
MotorEncapsulated
Continuous DutyYes
Efficiency Service Factor Load [%]86.00 %
Protection [IP]IP68
Hz50Hz/60Hz
Lead Wire SizeAWG #2
Poles2
S.F.1.15
Motor CoolingWater
Motor Ambient Temperature Rating Nominal167 °F
RotationCounter clockwise facing the shaft
Winding Resistance (Main Winding).04-.06
Thrust BearingKingsbury Type
SealMechanical Seal
Lead Insulation MaterialXLPE
Diaphragm MaterialFluoroelastomers FKM
Motor Fill Solution (Water Soluble / Non Toxic)Yes
Shaft Slinger MaterialNitrile Rubber (NBR)
Stator/ Motor Shell Material316 SS
Winding MaterialCopper
Motor Length85.78 "
Product Weight641 lb
Product Weight with Pack700 lb
Carton Length78.5 "
Carton Width9 "
Carton Height17 "
Shaft EndSpline
Warranty Standard Time12 Month Install / 24 Month Manufacturing
Repair Kit AvailableYes
Item #2791059204
Model8H3F(125HP,460/380,6/5)S
Series8-Inch Three Phase High-Temp Models
Product family8-Inch Encapsulated High-Temp Motor
SubTrol Heat SensorNo
Motor Diameter - Physical Diameter7.70"
Motor Insulation ClassificationF
Motor Shaft End - Material17-4SS
Motor Fill SolutionFES92
Shaft Diameter1.5 "
Minimum Cooling Flow.50 ft/sec
Motor AdapterDouble flange
Motor Bottom End Bell Material316 SS
Motor Top End Bell Material316 SS
Stator Ends Material316 SS
Stator FillResin
Type316 SS
Motor ConnectionDOL

منتجات مشابهة

طلمبات