UFB-14S
رقم القطعة: KOMATSU-UFB-14S
لا يعرض أي بائع سعرًا لهذا المنتج بعد.
للطلب والدفع استخدم تطبيق ENG.
الوصف
UFB-14S
المواصفات
| Throughput (standard) (MTPH) | Up to 1 360 |
|---|---|
| Throughput (standard) (TPH) | Up to 1,500 |
| Filtration | Pressure and return line |
| Seam height (cm) | Greater than 190 |
| Seam height (in) | Greater than 75 |
| Breaker pick force (kg) | Up to 40 823 |
| Breaker pick force (lbs) | Up to 90,000 |
| Electrical Compliance | Dust-Tight/ Non-Permissible |
| Machine voltage | 1,000 VAC @ 60 Hz |
| Control voltage | 120VAC @ 60 Hz |
| Control voltage type | 120 VAC @ 60 Hz |
| Recommended size | 2/0 FOR 1000V SHD-GC |
| Trailing cable | Supplied by customer |
| Trailing cable recommended size | Recommended Size: 2/0 FOR 1000V SHD-GC, supplied by customer |
| PLC - logic electric system | PLC - logic electric system: MicroLogix 1400 PLC with diagnostic display |
| Conveyor drive (HP) | 200 |
| (1) Breaker / conveyor drive (kW) | 150 |
| (1) Breaker / conveyor drive (HP) | 200 |
| (1) Breaker / conveyor drive voltage | 1,000 VAC @ 60 Hz |
| (1) Conveyor reversing / jogging drive (HP) | 5 |
| (1) Conveyor reversing / jogging drive (kW) | 3.7 |
| (1) Conveyor reversing / jogging drive voltage | 1,000 VAC @ 60 Hz |
| (2) Conveyor reversing / jogging drive voltage | Interlocked to prevent operation when main drive active. |
| Conveyor reversing / jogging drive | 5 HP (3.7 kW) |
| Conveyor reversing / jogging drive voltage | 1,000 VAC @ 60 Hz |
| Interlocked | To prevent operation when main drive active. |
| Conveyor start method | 3 photo eyes |
| Start-up warning horn | 20-second delay for start |
| Electrical operation | High oil temperature switch, vacuum switch, breaker speed switch. |
| E-stops | Push button and one oen each side of machine |
| Panic bar located at tram controls | 305 mm (12 in) tape switch |
| Tram enable | Push button |
| Electric breaker (kW) | 150 |
| Electric controller | PLC - logic electric system and microLogix 1400 PLC with diagnostic display |
| Electric motor voltage | 1,000 VAC @ 60 Hz |
| Machine voltage specifics | 1,000 VAC @ 60 Hz |
| Motor | Hagglunds CA70 hydraulic motor |
| Heat exchanger | Water/oil standard |
| Fill system | Single jet fill, located at hydraulic tank |
| Overall length (mm) | 10 923 |
| Overall length (in) | 430 |
| Tram width (mm) | 3 344 |
| Tram width (in) | 132 |
| Minimum tran height (in) | 38 |
| Minimum tran height (mm) | 965 |
| Intake length (mm) | 3 033 |
| Intake length (in) | 119 |
| Maximum discharge clearance (mm) | 762 |
| Maximum discharge clearance (in) | 30 |
| Estimated Mass (lbs) | 88,200 |
| Estimated Mass(kg) | 40 000 |
| Conveyor width - single conveyor (mm) | 1 422 |
| Conveyor width - single conveyor (in) | 56 |
| Chain tensioning (in) | 8 in stroke grease cylinders (one per side) with mechanical locking shims |
| Chain tensioning (mm) | 203 mm stroke grease cylinders (one per side) with mechanical locking shims |
| Rationing | (2) Material Restricting chains – removeable |
| Tail shift | 100 mm tailshaft with 100 mm take up bearings |
| Government regulatory requirements | Not required |
| State requirements | Not required |
| Funk Planetary Gear Drive | Free-wheeling capabilities |
| Crawlers (in) | 15 in forged pad width with triple chevron grousers on engineered chain |
| Crawlers (mm) | 381 mm forged pad width with triple chevron grousers on engineered chain |
| Chain tensioning | Grease cylinders with shim pack mechanical locks |
| Tram speed (FPM) | 47 |
| Tram speed (m/min) | 14.3 |
| Intake end ground clearance (in) | 2 - 22 |
| Intake end ground clearance (mm) | 51 - 559 |
| Discharge end ground clearance (in) | 2 - 22 |
| Discharge end ground clearance (mm) | 51 - 559 |
| Telescopic cylinders | Include pilot operated check valves |
| Mechanical elevation | Lock to isolate hydraulics |
| Lubrication features | Manual central lube |
| Color | Orange per standard 5100036338 (Screens painted flat black) |
| Throughput coal (60 lbf.-ft3) | 1,200 TPH |
| Throughput coal (962 kg/m3) | 1 100 MTPH |
| Throughput potash (75 lbf.-ft3) | 1,700 TPH |
| Throughput potash (1 201 kg/m3) | 1 550 MTPH |
| Throughput trona (75 lbf.-ft3) | 1,700 TPH |
| Throughput trona (1 201 kg/m3) | 1 550 MTPH |
| Throughput gypsum (80 lbf.-ft3) | 1,500 TPH |
| Throughput gypsum (1 281 kg/m3) | 1 350 MTPH |
| Max input size (in) | 16 |
| Max input size (mm) | 400 |
| Output size (in) | 8 |
| Output size (mm) | 204 |
| Conveyor width specifics (in) | 56 single conveyor |
| Conveyor width specifics (mm) | 1 422 single conveyor |
| Conveyor drive | Single shaft-mounted splined hydraulic motor and Hägglunds CA-70 or equivalent. |
| Head shaft (in) | 4.5-in head shaft with 3 15/16 in pillow block bearings and 9-tooth head shaft sprockets. |
| Head shaft (mm) | 114 mm head shaft with 100 mm pillow block bearings and 9-tooth head shaft sprockets. |
| Tail shaft (in) | 3.94 in tailshaft with 3.94 in take up bearings. |
| Chain & flights (in) | 3.5 in pitch, 220,000 lbf. ultimate strength per strand (440,000 lbf. total) with flight attachment pins every other pitch |
| Chain & flights (mm) | 89 mm pitch, 979 kN ultimate strength per strand (1 957 kN total) with flight attachment pins every other pitch |
| Alloy steel flights, forged flight ends (in) | 1.75 x 5 |
| Alloy steel flights, forged flight ends (mm) | 44 x 126 |
| Flight spacing every 6th pitch (in) | 21 |
| Flight spacing every 6th pitch (mm) | 533 |
| (2) Material Restricting chains | Removeable |
| Flat 3-way dump intake (in) | 123 in long |
| Flat 3-way dump intake (mm) | 3 124 mm long |
| Frame height (in) | 36 |
| Frame height (mm) | 914 |
| Conveyor wear deck | AR Plus |
| CCO side chain | Wear strips on top and return decks |
| Conveyor chain covers | Included |
| Top covers | Steel |
| Hinged rubber | Discharge chute |
| Hopper sideboards | 6 in folding |
| Breaker drive | Direct drive w/ splined connection to breaker shaft |
| Relief | Torque limiting clutch |
| Shaft | 200 mm diameter |
| Breaker (mm) | 610 mm breaker diameter |
| Breaker (in) | 24 in breaker diameter |
| Bearings specifics | 5 11/16 in |
| Breaker picks | 1-piece tapered shank and heat treated with carbide inserts |
| Weld-on holders | To be hard-surfaced |
| Hard surfacing | Yes |
| 5 nozzle spray bar (gpm) (psi) | 5.2 gpm @ 150 psi per nozzle |
| 5 nozzle spray bar (L/min) (bar) | 19.7 L/min @ 10.3 bar per nozzle |
| Pendulum valve | Activated when material is present in the conveyor |
| Water inlet location | Conveyor drive side |
